Mercedes S Class Mercedes S350, Mercedes S430, Mercedes S500 and Mercedes S600 Sedans.

Tilt/Telescopic lever "end" cap 2000/S430

Thread Tools
 
Search this Thread
 
  #1  
Old 10-14-2008, 06:40 AM
tomard's Avatar
Junior Member
Thread Starter
Join Date: Jun 2008
Location:
Posts: 27
Default Tilt/Telescopic lever "end" cap 2000/S430

Does anyone have, or know where I can get the little black end cap to the TILT/TELESCOPIC STEERING LEVER, that is the bottom lever, below the Windshield wiper & turn signal levers, on a 2000 S430 (without buying/replacing the whole lever ) ?????[/align]
 
  #2  
Old 10-14-2008, 07:04 PM
chassis221's Avatar
Senior Member
Join Date: Feb 2007
Location: Philadelphia, Pa
Posts: 2,691
Default RE: Tilt/Telescopic lever "end" cap 2000/S430

im sure you wont find that as a seperate piece.
 
  #3  
Old 10-14-2008, 07:30 PM
tomard's Avatar
Junior Member
Thread Starter
Join Date: Jun 2008
Location:
Posts: 27
Default RE: Tilt/Telescopic lever "end" cap 2000/S430

I figured as much, just hoped that someone had replaced their entire lever and had one I could get ........
 
  #4  
Old 10-14-2008, 09:07 PM
chassis221's Avatar
Senior Member
Join Date: Feb 2007
Location: Philadelphia, Pa
Posts: 2,691
Default RE: Tilt/Telescopic lever "end" cap 2000/S430

i have a cruise control switch.. not sure from what car though. might be the same end cap. maybe it can pop off.
 
  #5  
Old 10-14-2008, 09:15 PM
tomard's Avatar
Junior Member
Thread Starter
Join Date: Jun 2008
Location:
Posts: 27
Default RE: Tilt/Telescopic lever "end" cap 2000/S430

I will go out tomorrow and check mine ..... and take a measurement of "hole".
Would be great if it was same!!!!
 
  #6  
Old 10-15-2008, 10:20 AM
chassis221's Avatar
Senior Member
Join Date: Feb 2007
Location: Philadelphia, Pa
Posts: 2,691
Default RE: Tilt/Telescopic lever "end" cap 2000/S430

it does pop off ..the one i have has arrows on it and it is a little bit longer than the stalk for the telescoping wheel but it should work. ill post a pic for you in a bit
 
  #7  
Old 10-15-2008, 04:02 PM
tomard's Avatar
Junior Member
Thread Starter
Join Date: Jun 2008
Location:
Posts: 27
Default RE: Tilt/Telescopic lever "end" cap 2000/S430

Looks good - do you think I will be able to smooth out the arrows and paint it?
How much do you want for it? The "hole" in my lever is about 5/8", but looks the same as the cruise lever!
Tom
 
  #8  
Old 10-15-2008, 04:42 PM
chassis221's Avatar
Senior Member
Join Date: Feb 2007
Location: Philadelphia, Pa
Posts: 2,691
Default RE: Tilt/Telescopic lever "end" cap 2000/S430

the arrows are only on one side and it looks even all the way around. so you could just flip it around and it looks like it will work.. like i said its just about a few mm longer than whats supposed to be on there. but im sure it will work,i dont really want anything for it, you can have it.
 
  #9  
Old 10-15-2008, 05:06 PM
tomard's Avatar
Junior Member
Thread Starter
Join Date: Jun 2008
Location:
Posts: 27
Default RE: Tilt/Telescopic lever "end" cap 2000/S430

Thanks SO much! Really appreciate it a lot.
I will pm you my info.
Tom
 
  #10  
Old 10-16-2008, 07:05 PM
tomard's Avatar
Junior Member
Thread Starter
Join Date: Jun 2008
Location:
Posts: 27
Default RE: Tilt/Telescopic lever "end" cap 2000/S430

Did you get my address??
 


Quick Reply: Tilt/Telescopic lever "end" cap 2000/S430



All times are GMT -5. The time now is 03:09 AM.